NEW 12 / 24 Volt 150 PSI 3/4HP Air Ride Air Suspension Compressor 2yr Warranty

This listing is for 1 - BRAND NEW 12V or 24V Air Compressor. Used in a wide variety of applications. These include Air Suspensions, Air slides, RV leveling systems, on demand air, air horns, Air Brakes, Pond Aeration - off grid septic and wasterwater Pumps, and many more!

These can replace the much more expensive Thomas and Gast brands - comparable to the TA-4101, TA-3101, 270025, 270024, and many more. Provided in this kit is our Very Own DIY Pond's oil less, 12 or 24 volt air compressor. This base kit is designed for the "Do It Yourselfer". Who wants a performance air compressor to build a personalized air system for their vehicle. Pressure switches, air tanks, solenoid valves, relays, manifolds, airline and fittings to help complete your air system. NOTE -- BEFORE STARTING: These COMPRESSOR REQUIRE. The use of a unloader assembly kit, for use with an air tank.

Available as an add-on in the link above. These add-on Kits include the following. Hi temp discharge line to dissipate the heat created by compressing air. 12 gage power supply wire if compressor is located within 10 ft of the positive battery terminal.

8 gage power supply wire if the compressor is mounted 10 to 20 ft from the positive battery terminal. It is recommended to have the compressor located as close to the supply as possible. Do not exceed 20 ft.

Unloader valve to exhaust the air within the discharge line for easier compressor start-up. Circuit breaker to protect the electrical circuit at the positive battery terminal connection. Pressure switch controls min and max pressure of the air tank, 110 psi ON 135 psi OFF. One way check valve to prevent air from bleeding back through the compressor head.

Must be secured to a firm and level surface and can be. Must be mounted high enough on the vehicle to avoid being. Must mount in a dry area, not exposed to rain or wheel spray.

Do not install under the hood near the engine, insufficient. Must be in a well ventilated area for cooling.

Located in the end cap; do not obstruct the fans intake ports. The compressor has two ports at the cylinder head. Remove the pipe plug installed at our factory; only use the.

Female NPT port for the air discharge line. When installing the discharge line, it must slope downwards. To the air tank to prevent moisture from collecting in the line.

(which could freeze in cold weather rendering the compressor inoperative). 12V HP3/4HP Series Air Compressor is a heavy duty compressor with vertical pump head configuration. These Air Compressors have a 100 percent duty cycle and are offered in two pump head configurations-Vertical and Horizontal. Copper wire wound permanent magnet motor. Hard anodized aluminum cylinder and aluminum sleeve.

100 percent at 100 PSI duty cycle. Size is 11.5 inch x 6 inch x 9.5 inch or 293 mm x 153 mm x 242 mm (LxWxH). Weight is 17.7 lbs. The heavy duty 12 VDC (Volts of Direct Current) and 24 VDC air compressors are ideal for filling air tanks for both the on and off-road markets.

The popular 12 VDC compressors are offered in two pump head configurations, vertical and horizontal. These 3/4 horsepower compressors have an oil-less design, sealed bearings, PTFE piston ring, copper wire wound permanent magnet motor and a cast cylinder with a hard anodized aluminum sleeve.

Mountable in any orientation - So mounting configuration does NOT Matter - unless your space does. 150 PSI Max Working Pressure, Draws 22.5 AMPs. 158°F Max / -40°F Min Ambient Temperature. This item is in the category "Home & Garden\Tools & Workshop Equipment\Air Tools & Air Compressors\Air Compressors".

The seller is "diypondaeration" and is located in this country: US. This item can be shipped to United States.

HP Rating: DIY 12 VOLT Pump Plus ADD on Unloader Kit
Horse Power: 3/4
Flow Rate: 3.1 cfm
Maximum Working Pressure: 150 PSI
Portability: Stationary
Tank Capacity: 6 gal
Power Source: Hard Wire
Type: Air Compressor
MPN: DIY3/4625SD
Lubrication Type: Oil-Free
Brand: DIY Pond
Voltage: 12 V